Overview
The Powerslide Radon 80 Skates are a special makeup (SMU) priced to entice folks try out Powerslide's trinity mounting system. Trinity mounting is incredibly low to the ground, stable and easy to skate. Combined with supportive and comfortable powerknit uppers and aluminum frames, it is a safe bet on their part that you will enjoy them. Should you want to change wheel configurations later on, the Radon 80 is compatible with any trinity mount frame. Out of the box it comes with 80mm 85A wheels with ABEC5 bearings.
Skate Type | Recreational |
---|---|
Skill Level | Beginner and Intermediate |
Weight | 1320g (US 8.0 EU 41) |
Specifications
KEY TECHNOLOGIES | |
---|---|
Trinity X Mounting The combination of the 'along' mounting block of the boot with the 'across' mounting slot of the frame. This allows for frame adjustment both laterally (7mm) and front to back (8mm) to individual preference and/or to correct ankles from wanting to roll (pronation/supination). Trinity frames mount at three points with two off-set winged mounts under the ball of the foot that creates a channel for the wheels to lower the skate, adding stability and power at push-off. |
|
HABS Height Adjustable Brake System An easy and secure brake that allows for the brake pad to adjust up and down to prolong the life of the rubber. A rear axle that is threaded at both ends allows for the installation and removal of the brake with four outer screws that eliminate having to remove the axle or wheel. |
BOOTS | |
---|---|
Construction | Soft Boot |
Cuff | Standard |
Liners | Fixed - Not Removable |
Heat Moldable | No |
Closures | Cuff Buckle 45 Degree Velcro Power Strap Standard Lacing |
Mounting | Trinity |
FRAMES | |
---|---|
Material | Casted Aluminum |
Mounting | Trinity |
Length | Sizes 5.0 - 8.0 (EU36-41) 9.6” Axle to Axle Sizes 8.0 - 12.5 (EU42-47) 10.8" Axle to Axle |
Removable | Yes |
Adjustable | Yes |
Stock Wheel Setup | 4x80mm |
Max Wheel Size | 80mm |
Axles | One-Piece 8mm |
COMPONENTS | |
---|---|
Wheels | Powerslide Phuzion 80mm 85A |
Bearings | Wicked ABEC5 |
Brake | Yes |
Axle for Brake Removal | Included |
Skate Tool | Included |
MANUFACTURER and WARRANTY INFORMATION | |
---|---|
Model Number | 901975 |
Time | 2 Years |
Contact | Inline Warehouse |
Country of Origin | China |
Sizing Chart
GENERAL SKATE SIZING GUIDELINES | |
---|---|
Measure both feet with socks similar to those in which you intend to skate. Then use the measurement of the longest point and reference the model-specific size chart to determine size. How to Measure Your Feet for Skates. | |
Proper fit has the toes not being cramped against the front. Toes may slightly brush the front as heels will settle back when in the skating position. Try on skates indoors while in a seated position. Lace and buckle both skates, tap your heels to the floor, and then stand and bend your knees to simulate the skating position. How to Try on Inline Skates for Fit. | |
FIT GUIDELINES: Use foot measurement for the most precise fit. Add .5cm to the measurement for extra room at the toe or if wider feet. |
Radon Size | CM | EU |
---|---|---|
5.5 | 23.6 | 37 |
6.0 | 24.2 | 38 |
7.0 | 24.8 | 39 |
7.5 | 25.5 | 40 |
8.0 | 26.1 | 41 |
9.0 | 26.8 | 42 |
10.0 | 27.5 | 43 |
10.5 | 28.2 | 44 |
11.0 | 28.9 | 45 |
12.0 | 296 | 46 |
12.5 | 30.3 | 47 |